athilt.blogg.se - Gabotronics xscope

#Gabotronics xscope generator#
#Gabotronics xscope driver#
#Gabotronics xscope manual#
#Gabotronics xscope software#
#Gabotronics xscope Pc#

Remember the Rigol does not meet my spec of <100 so I still have to get the Xminilab. I ordered a Rigol DS1054Z today for 375.06 from Tequipment (with eevblog discount - thanks) to test the Xminilab.

#Gabotronics xscope generator#

C Compiler, included in the WinAVR package: WinAVR at sourceforgeĢ) Can the waveform generator and the oscilloscope run simultaneously?.Integrated Development Environment: Atmel Studio 6.1) What tools do I need to develop my own programs on the XScope?īesides the power supply, you need an external programmer, such as the AVR ISP 2, or a debugger, such as the AVR JTAGICE mkII or the AVR ONE!. Re: XSCOPExmega-xminilab oscilloscope cheap small not as good as Rigol. Yes, the waveform generator runs on the background. This project is aimed at producing a GUI framework for using that driver.

#Gabotronics xscope driver#

The node-xscope project was aimed at producing a driver package for a Gabotronics Xminilab oscilloscope module, which should be easy to use in small coffeescript scripts run from the command-line. (The AWG uses the DMA, so it doesn't need any CPU intervention). A HTML-based GUI for my node-xscope project. The device can be powered thru the micro USB port. Do not connect a 5V power supply and the USB at the same time.Ĥ) Can I connect the XScope to the computer to control the oscilloscope and get the data? Alternatively, the device can be powered by connecting a 5V power supply on the 5V pin.

#Gabotronics xscope Pc#

Old hardware 1.4 and 1.5 cannot do USB firmware upgrades.Ī UART to USB cable is required for hardware 1.4 and 1.5.ĥ) Can I connect the XScope to the computer using the USB for firmware updates? Yes, you can use the XScopes PC Interface. This is the maximum current on each voltage: The XScope can also power external devices. +5V: Will be the same as the power source minus 60mA. +3.3V: Approximately 200mA, but this subtracts from the available current on the +5V line.ħ) What is the maximum frequency that I can measure with the XScope? 5V: Approximately 50mA, but this subtracts from the available current on the +5V line. Graphic OLED, 128圆4 pixels, max.However, you can still measure frequencies up to almost Nyquist/2, i.e. USB connectivity: Windows, Linux, MAC, AndroidĪTXMEGA32A4U 32KB+4KB Flash, 4KB SRAM, 1KB EEPROM.

#Gabotronics xscope manual#

: Schematics XScopes User’s Manual 12.2 Schematics Figure 78: Xprotolab Schematic DS-XScopes-3.5 December, 2014.

Horizontal and Vertical Cursors with automatic waveform measurements, and waveform references. Figure 76 shows the XScope’s Architecture block diagram.

XScopes User’s Manual Page DS-XScopes-2.2 September, 2012 2.

Channel Math: add, multiply, invert, and average. Figure 1: Xprotolab and Xminilab, Top View Figure 2: XScopes Block Diagram.

Spectrum Analyzer with different windowing options and selectable vertical log and IQ visualization.

XY Mode: For plotting Lissajous figures, V/I curves or checking the phase difference between two waveforms.

Meter Mode: VDC, VPP and Frequency readout.

Advanced Triggering System: Normal / Single / Auto / Free, with many trigger modes adjustable trigger level, and ability to view signals prior to the trigger. The XScopes (Xminilab and Xprotolab) are a combination of three electronic instruments: a mixed signal oscilloscope, an arbitrary waveform generator, and a.

Arbitrary Waveform Generator with advanced sweep options on all the wave parameters.

void xscopeconfigio(xscopeIORedirectionModemode) Congures XScope I/O redirection. Visualization of the signals and controlling the device can be done through an open-source PC interface software.

It’s a nifty little (1 x 2-in.) mixed-signal oscilloscope module blended with a logic analyzer and arbitrary waveform generator. This function has the following parameters: id XSCOPE probe id. The 20 Xprotolab Plain from Gabotronics is one such good option.

Mixed Signal Oscilloscope: Simultaneous sampling of 2 analog and 8 digital signals. void xscopechar(unsigned char id, unsigned char data) Send a trace event for the specied XSCOPE probe of type char.

The Xprotolab and Xminilab can be plugged directly on a breadboard. The XScopes can also be used as development boards for the AVR XMEGA microcontroller. The PC interface has been rewritten in the Qt framefork so. The user interface is 4 buttons, and a real pain to use. Ive got one permanently fixed on my breadboard, but I wouldnt reccomend it. Then I saw the Gabotronics Xscope at a maker fair and bought one.

Mainly what it did was sit on a shelf because all the buttons, knobs and attachments were confusing and all the online resources I found were a bit beyond my understanding at that point.

#Gabotronics xscope software#

The XScopes are a combination of three electronic instruments: a mixed signal oscilloscope, an arbitrary waveform generator and a protocol sniffer. This software is used to interface to Gabotronics line of oscilloscopes (Xprotolab / Xminilab). The only low-cost dual trace with onboard display I know of is the Gabotronics Xscope. It had a ton of features and accessories and it could do a lot.